Farmer-Helper FH-EFGC155 vs WoodMaxx FM-62 hammer: actual swath and order specification
FH-EFGC155 publishes a 60-inch cut; the fixed FM-62 hammer cuts 55 inches despite its larger model number. Both comparisons exclude hydraulic side shift. The Farmer-Helper’s dated price was $1,222 lower, but its power and supplied-parts conflicts need resolution before that wider swath becomes a purchase case.
By Acreage Equipment · Reviewed November 7, 2026 · Specification research, not a field test
Farmer-Helper FH-EFGC155 · Hammer blades: when to shortlist itConsider when the 60-inch cut is useful and Betstco confirms the exact hammer order, acceptable tractor power, delivered shaft/belts and complete operating load.
WoodMaxx FM-62 · Hammer blades: when to shortlist itConsider when the 55-inch cut,24–45 PTO hammer band and slip-clutch configuration suit the tractor and job, after reconciling weight and confirming fixed placement.
Dated official U.S. listing observations from November 7, 2026. These are base/configuration references, not delivered quotes; optional kits, setup, taxes and freight services are uncalculated. Open your saved comparison →
The Farmer-Helper provides 5 more inches of published cut in a 2-inch-wider page body dimension. Verify actual edge placement; the FM-62 name is not a 62-inch cut.
FH-EFGC155: 25–65 PTO hp in current Details, with manual and 50 HP additional-table conflicts. FM-62 hammer: 24–45 PTO hp in current manual.
The WoodMaxx hammer maximum is 45 PTO hp. Do not use its generic 20 hp page minimum for hammers or assume Betstco’s 65 PTO upper figure is resolved against the linked manual.
FH-EFGC155: 24 hammers; 48 Y blades offered; page advertises interchangeability. FM-62 hammer: 18 hammers; page says Y and hammer machines are not interchangeable.
Spare-set quantities and future blade-choice paths differ. Obtain exact compatible Farmer-Helper parts and procedures; counts do not establish finish or material capacity.
FH-EFGC155: included shear-bolt shaft; Series 5 main/manual versus Series 4 additional-table conflict. FM-62 hammer: included slip-clutch shaft; 39 lb shaft reference separate from body mass.
Compare replacement protection parts and setup requirements, then confirm the actual shaft. Neither protection type is a verified durability advantage.
Farmer-Helper FH-EFGC155 · Hammer blades: when to shortlist it
Consider when the 60-inch cut is useful and Betstco confirms the exact hammer order, acceptable tractor power, delivered shaft/belts and complete operating load.
WoodMaxx FM-62 · Hammer blades: when to shortlist it
Consider when the 55-inch cut,24–45 PTO hammer band and slip-clutch configuration suit the tractor and job, after reconciling weight and confirming fixed placement.
The current product details explicitly label the range as PTO horsepower. The currently linked manual is Revision 12-12-17 despite its /2025/05/ upload path: p 23 has a minimum-HP footnote that changes basis to engine horsepower for hydrostatic tractors, while p 16 states an 80 PTO hp ceiling. These sources do not establish one reconciled limit for the delivered machine.
FH-EFGC155 has internal 50 HP, belt-count and shaft-series conflicts.
FM-62 manual 774 lb product weight differs from page 641 lb body+39 lb shaft; complete operating load is not established.
WoodMaxx generic 20–45 PTO page range must not replace its hammer-specific 24–45 manual range.
Current official product pages and manufacturer-linked manuals were checked November 7, 2026. The EFGC manual is Revision 12-12-17 despite its later upload directory. These are published-specification comparisons, not field tests or confirmed tractor pairings.
FOLLOW THE NUMBERS
Sources & documentation
Research record reviewed November 7, 2026. Confirm the current manual and the exact revision supplied with your machine.
