Land Pride FM2560 hammer vs TMG TFM60: the same nominal cutting width
A 60-inch label hides several useful differences here. FM2560 has documented center and right-offset mounting choices and a selected 16-hammer rotor. TFM60 lists 24 flail hammers and a separate 50-PTO-hp ceiling in its manual. Both have unresolved horsepower-basis or weight questions, so start with the intended placement and tractor limits rather than the shared width label.
By Acreage Equipment · Reviewed November 8, 2026 · Specification research, not a field test
Consider FM2560 when its mounting choice mattersShortlist the hammer-equipped FM2560 where its documented center/8-inch-right positions answer the job.
Consider TFM60 for a fixed-position 60-inch jobShortlist TFM60 where a fixed mower and its published 1-1/2-inch material guidance suit the work, the tractor does not exceed 50 PTO hp and TMG reconciles the generic power band and weight figures.
Prices shown on the product cards retain their original check dates. This comparison does not rank total purchase cost. Obtain current itemized quotes for the exact configuration, shaft, setup and delivery. Open your saved comparison →
The differences that matter.
01
Published power band versus a separate PTO ceiling
FM2560: 33–80 tractor hp, with engine/PTO basis unspecified. TFM60: 30–60 HP with basis unspecified, plus a manual instruction that tractor power must not exceed 50 PTO hp.
The TMG 50-PTO-hp ceiling is a distinct check, not a reinterpretation of its generic 60-hp label. Ask both makers to identify the main power basis; do not convert Land Pride’s gearbox rating into a PTO ceiling.
FM2560: Category I, with center or 8-inch-right hitch positions. TFM60: fixed Category I mower; the reviewed exact-model sources do not document an equivalent two-position offset choice.
For an orchard row or edge that needs a deliberate offset, Land Pride provides a documented mounting alternative to investigate. Ask TMG for actual cutter-edge placement rather than assuming the same reach. Neither is the hydraulic side-shift model.
FM2560 selected hammer rotor 333-135A carries 16 hammers; a different blade style requires a complete matched rotor assembly and dealer change per the manual. TFM60’s table lists 24 flail hammers; no equivalent alternate-rotor conversion is established in the reviewed sources.
Choose the intended cutting configuration in the quote and compare the correct replacement sets. More hammers is a parts quantity, not proof of better finish or more throughput.
FM2560 hammer capacity is 2 inches in the manual/FAQ but 1.5 inches in the catalog feature. TFM60 page lists 1-1/2-inch cutting thickness.
Land Pride’s conflicting capacity labels prevent a settled diameter advantage over TMG. Obtain model-specific advice on species, moisture and travel speed. These are manufacturer claims, not a common field test or a guarantee at minimum power.
FM2560 manual’s 965-lb unit figure explicitly includes a duckfoot rotor, not the selected hammer configuration; its brochure lists 929 lb without a rotor basis. TFM60 page calls 650 lb the operation weight, while the linked manual lists 270 kg product weight.
Request complete delivered hammer-machine weights and load centers. Do not add Land Pride’s 222-lb hammer rotor to an already rotor-inclusive unit figure, or resolve TMG’s conflict by choosing whichever number passes a lift check.
FM2560 manual states 60-inch working width and 72-inch overall width. TFM60 page states 60-inch working width and a 65 × 42 × 30-inch L × W × H envelope, but its manual table says 1,550 mm cutting width, about 61 inches.
Confirm which delivered dimensions describe the mower’s transverse body and actual cut before planning access or tire coverage. The TMG inch/mm mismatch is not used to claim an extra inch of usable swath.
Shortlist the hammer-equipped FM2560 where its documented center/8-inch-right positions answer the job. Resolve the conflicting 1.5/2-inch material labels, 33–80-hp basis, hammer operating mass and exact rotor/shaft/rake quote before choosing.
Shortlist TFM60 where a fixed mower and its published 1-1/2-inch material guidance suit the work, the tractor does not exceed 50 PTO hp and TMG reconciles the generic power band and weight figures. Confirm actual cutting-edge placement and working width.
Both main horsepower bands leave engine/PTO basis unspecified; TMG additionally publishes a 50-PTO-hp maximum. None of those labels may be silently substituted for another.
FM2560’s manual unit weight is for a duckfoot rotor and differs from the unlabeled brochure value. TFM60 operation weight on the page conflicts with its manual product weight.
TMG’s linked file name includes 2025.01.09, but the cover reads v.2022.11.29. The filename is not treated as a revised specification date.
TMG lists 60 inches on the page and 1,550 mm in the manual; the working-width mismatch remains unresolved.
Land Pride calls the brush rake optional in assembly instructions and the brochure, but standard in the p39 count row. Inclusion must be stated in the quote.
Land Pride’s current FM25 catalog conflicts internally: its Three Blade options feature states 1.5-inch hammer capacity, while its cutting-capacity FAQ and July 1, 2024 manual p39 state 2 inches. Confirm the delivered configuration and material conditions; no settled capacity advantage is claimed.
Primary manufacturer pages and linked manuals were checked on November 8, 2026. Document revisions and known conflicts are kept distinct from the check date. These are specification comparisons, without physical tests or confirmed tractor pairings. Hammer-capacity wording was specifically rechecked November 8, 2026; the remaining specification and price observations retain their stated dates.
FOLLOW THE NUMBERS
Sources & documentation
Research record reviewed November 8, 2026. Confirm the current manual and the exact revision supplied with your machine.
