Land Pride FM2560 vs WoodMaxx FM-62: hammer configurations
These hammer-equipped mowers both use fixed positioning, with different cutting widths and mounting choices. FM2560 cuts 60 inches and offers center or right-offset mounting; the WoodMaxx cuts 55 inches with one documented fixed placement. Start with the swath and placement needed around your tractor, then resolve the horsepower labels and complete rear load.
By Acreage Equipment · Reviewed November 8, 2026 · Specification research, not a field test
FM2560 · hammer rotor: when to shortlist itConsider FM2560 when a 60-inch swath and a choice of center or 8-inch-right mounting solve a specific coverage problem, provided the dealer clarifies its 33–80 tractor-hp basis, hammer mass and shaft fit.
FM-62 · hammer blades: when to shortlist itConsider the fixed FM-62 hammer configuration when a 55-inch cut and its fixed placement suit the job, the tractor is within the documented 24–45 PTO-hp range, and the complete load and shaft setup are verified.
The WoodMaxx black/hammer option FM-62-0006 was displayed at $3,630 USD on 2026-11-07; this is a dated product-price observation, not a delivered total. No current official Land Pride numeric price was captured, so request an itemized quote. No claim that either is cheaper is supported. Open your saved comparison →
Use working width for coverage and verify the outside envelope for access, storage and transport. Neither model number is an exact substitute for those two measurements.
FM2560 · hammer rotor: 33–80 tractor hp; engine-versus-PTO basis is unspecified. Shared model range with no separate hammer band. FM-62 · hammer blades: 24–45 PTO hp for hammer blades in the current manual.
The two labels are not equivalent. Obtain the Land Pride basis and compare each requirement against the correct tractor specification; do not decide which mower requires less power from these numbers alone.
FM2560 · hammer rotor: Fixed mounting choice: center or 8 inches right. No hydraulic side-shift circuit is documented. FM-62 · hammer blades: Fixed 29 inches left and 36 inches right of the published PTO/center reference.
Measure actual cut placement relative to the tractor tires. Land Pride’s displacement and WoodMaxx’s center-reference extents are different dimension types, so do not subtract them to rank reach.
FM2560 · hammer rotor: Seven manual settings from 0 to 6 inches in 1-inch increments. FM-62 · hammer blades: Published cutting-height range 3/4 to 3-3/4 inches.
Compare the intended stubble height with the documented range. Zero is a published adjustment setting, not advice to scalp the ground; follow setup and terrain instructions.
FM2560 · hammer rotor: 16 hammers in selected rotor assembly 333-135A. The manual documents dealer replacement of the complete matched rotor to change blade style. FM-62 · hammer blades: 18 individual hammers. Current product page warns that Y-equipped and hammer-equipped mowers are not interchangeable.
Choose blade configuration explicitly in both quotes. Land Pride describes an alternative complete-rotor route; no equivalent conversion or cost is verified for WoodMaxx. Counts do not prove durability, cutting quality or running cost.
FM2560 · hammer rotor: Manual/FAQ list 2-inch hammer material, while the current catalog feature says 1.5 inches. FM-62 · hammer blades: Current page describes hammer use for saplings 1 inch diameter or less.
These are different manufacturer claims, not a common performance test. Ask each seller about species, moisture, travel speed and the actual tractor; neither number guarantees full-diameter work at minimum power.
Consider FM2560 when a 60-inch swath and a choice of center or 8-inch-right mounting solve a specific coverage problem, provided the dealer clarifies its 33–80 tractor-hp basis, hammer mass and shaft fit.
Consider the fixed FM-62 hammer configuration when a 55-inch cut and its fixed placement suit the job, the tractor is within the documented 24–45 PTO-hp range, and the complete load and shaft setup are verified. Do not use the page’s generic 20-hp minimum for hammers.
Land Pride does not identify engine versus PTO horsepower; the catalog keeps the basis unspecified and requires review.
Neither compared configuration has a verified complete shaft/options-inclusive operating load. Land Pride manual weights are duckfoot-specific and some brochure values differ; WoodMaxx manual product weights differ from current page mower-only figures.
Land Pride’s rake inclusion conflicts between assembly/brochure and one manual table row.
WoodMaxx page overall widths and manual product-dimension labels are not reconciled; obtain the delivered machine drawing.
FM-62 page’s generic 20–45 PTO-hp header does not identify the hammer minimum. The current manual specifies 24–45 PTO hp for hammers; do not silently apply the Y-blade minimum.
Land Pride’s current FM25 catalog conflicts internally: its Three Blade options feature states 1.5-inch hammer capacity, while its cutting-capacity FAQ and July 1, 2024 manual p39 state 2 inches. Confirm the delivered configuration and material conditions; no settled capacity advantage is claimed.
Manufacturer specifications and linked manuals reviewed November 7, 2026. Exact configuration and unresolved source differences remain part of the decision. No physical product test or confirmed tractor pairing is claimed. Hammer-capacity wording was specifically rechecked November 8, 2026; the remaining specification and price observations retain their stated dates.
FOLLOW THE NUMBERS
Sources & documentation
Research record reviewed November 8, 2026. Confirm the current manual and the exact revision supplied with your machine.
