Land Pride FM2572 hammer vs TMG TFM60: a wider fixed swath
FM2572’s selected hammer rotor cuts 72 inches inside an 84-inch overall body. TFM60 is marketed as a 60-inch mower with Category I mounting. For a wider tractor or a broad mowing route, Land Pride’s extra swath and Category II option are meaningful reasons to investigate it, but the complete hammer load and the basis of its 42–80 tractor-hp range need confirmation.
By Acreage Equipment · Reviewed November 8, 2026 · Specification research, not a field test
Consider FM2572 when the 72-inch swath and Category II option are neededShortlist the hammer-equipped FM2572 when its larger cut or defined center/10-inch-right mounting positions solve the route and tractor geometry.
Consider TFM60 when the nominal 60-inch job is enoughShortlist TFM60 when a Category I mower of its stated size covers the work and the tractor does not exceed the manual’s 50-PTO-hp ceiling.
Prices shown on the product cards retain their original check dates. Prices were not refreshed for this comparison, and no purchase-cost ranking is made. Request current itemized quotes for the exact configuration, shaft, setup and delivery. Open your saved comparison →
The differences that matter.
01
A twelve-inch nominal increase also widens the body
FM2572 specifies 72 inches working width and 84 inches overall width. TFM60’s page specifies 60 inches working width and a 65 × 42 × 30-inch L × W × H envelope, while its manual gives 1,550 mm cutting width, approximately 61 inches.
A wide tractor track or mowing route may justify investigating FM2572’s larger swath, while access and turning room may favor TFM60’s smaller stated envelope. Confirm which dimension describes the TMG’s transverse body and resolve its cut-width mismatch before planning coverage.
An unlabeled tractor range versus a separate PTO ceiling
FM2572 specifies 42–80 tractor hp without saying engine or PTO output. TFM60 specifies 30–60 HP without a basis, and its manual separately says the tractor must not exceed 50 PTO hp. Land Pride’s 80-hp gearbox rating does not resolve its tractor-power basis.
A tractor above 50 PTO hp cannot use TMG’s generic 60-hp headline to bypass the manual ceiling. Conversely, a tractor near 42 engine hp should not be treated as meeting Land Pride’s minimum until that maker identifies the intended rating.
Documented Category II and offset positions versus uncertain hand adjustment
FM2572 supports Category I or II and documented center or 10-inch-right mounting positions. TFM60 specifies Category I; its manual says the hitch can be adjusted side to side using a handle, but the reviewed exact-model sources do not establish the displacement or cutting-edge positions. Neither compared mower has a documented hydraulic side-shift circuit.
FM2572 offers a defined mounting arrangement to investigate for a Category II tractor or a repeatable right-offset pass. Ask TMG whether the handle instruction applies to the delivered TFM60 and what it actually moves, rather than calling the machine immovable or inventing an offset distance.
FM2572’s selected rotor assembly 333-136A carries 20 hammers; changing blade style requires a different complete rotor installed by a dealer. TFM60’s manual lists 24 flail hammers. Land Pride’s current feature says 1.5-inch hammer capacity, while its FAQ/manual say 2 inches; TMG’s page claims 1-1/2-inch cutting thickness.
Specify the exact rotor and spare parts in each quote. Neither the higher TMG hammer count nor Land Pride’s disputed larger material figure establishes a performance advantage. Ask for guidance on the actual vegetation, moisture and travel conditions.
FM2572’s manual identifies brush rake kit 333-092A and accessory quick-hitch driveline 826-883C. Its assembly text calls the rake optional, while a specification row calls the rakes standard. TFM60’s page explicitly includes a PTO driveline and storage kickstand, but does not establish that the shaft fits every quick-hitch installation.
Have the Land Pride quote identify the hammer rotor, rake choice and any alternate shaft separately. For TMG, identify the actual supplied driveline and protection parts. Do not equate a general shaft-included statement or a quick-hitch label with completed tractor setup.
Land Pride’s reference unit has the wrong rotor for a lift comparison
FM2572’s 1,040 lb manual unit weight explicitly includes a duckfoot rotor. The separate hammer rotor is 261 lb, which must not simply be added to that already rotor-inclusive unit. TFM60’s page calls 650 lb its operation weight, but the manual lists 270 kg, about 595 lb; shipping is separately listed at 680 lb.
Request the complete FM2572 hammer operating mass with the selected rake and shaft, plus a reconciled TFM60 operating weight. These sources flag a potentially important load difference but do not establish the exact assembled weights for a lift or ballast decision.
Consider FM2572 when the 72-inch swath and Category II option are needed
Shortlist the hammer-equipped FM2572 when its larger cut or defined center/10-inch-right mounting positions solve the route and tractor geometry. Resolve the horsepower basis and complete hammer load, then obtain an itemized rotor, rake, shaft and setup quote.
Consider TFM60 when the nominal 60-inch job is enough
Shortlist TFM60 when a Category I mower of its stated size covers the work and the tractor does not exceed the manual’s 50-PTO-hp ceiling. Resolve its main power basis, exact width, hand-adjustment applicability and conflicting operation-weight figures before ordering.
Both main tractor-horsepower bands leave engine/PTO basis unspecified. TMG’s separate 50-PTO-hp ceiling remains a distinct limit, while Land Pride’s gearbox rating does not supply the missing tractor basis.
TMG’s manual mentions side-to-side handle adjustment without an exact TFM60 distance, despite the product being the nonhydraulic TFM model. Fixed here means no documented hydraulic side shift, not proven absence of manual placement adjustment. The page/manual cut width also differs: 60 inches versus 1,550 mm.
Land Pride’s live catalog conflicts internally: Three Blade options says 1.5-inch hammer capacity and its cutting-capacity FAQ says 2 inches, matching manual p39. Feature and FAQ update dates differ, but both remain current catalog content. A settled material-size advantage over TMG is not established.
FM2572’s manual 1,040 lb unit weight includes a duckfoot rotor, not the selected hammer assembly; a complete hammer operating load is unknown. TMG’s 650 lb operation figure conflicts with its 270 kg manual product weight. Neither its 680 lb freight weight nor Land Pride’s separate rotor weight resolves the operating load.
Land Pride calls the brush rake optional in assembly instructions but standard in its specification count row. TMG’s manual filename contains 2025.01.09 while its cover reads v.2022.11.29; the filename is not treated as a revised specification date.
Official manufacturer pages and manuals were reviewed on November 8, 2026. Land Pride references use manual 333-138M dated July 1, 2024. TMG’s current linked filename contains January 9, 2025, but its cover is marked v.2022.11.29. Land Pride’s current catalog itself contains conflicting hammer-capacity labels.
FOLLOW THE NUMBERS
Sources & documentation
Research record reviewed November 8, 2026. Confirm the current manual and the exact revision supplied with your machine.
