John Deere 3033R · FLAIL MOWERS
For the U.S. 1368LV open-station eHydro scope, 24.3 PTO hp is only 0.3 above the FM62 hammer minimum. The same 55-inch FM62 with Y-blades has a lower 20-hp minimum, while FM78 starts at 30. The 3R hitch’s larger lift reference does not widen those power bands.
By Acreage Equipment · Reviewed November 8, 2026 · Specification research, not a field test
PUT THIS GUIDE TO WORK
See published mismatches and the checks still needed.
BEST MATCHES FOR THE 3033R
15 of 23 flail mowers we track pass the published power, hitch and speed screen. Each still has a detail to confirm with the seller.
Flail mowerWoodMaxx
47″ cutting width · 15–25 PTO hp · Y-blades only
Resolve the conflicting published specifications for the exact model revision.
Flail mowerWoodMaxx
55″ cutting width, inches · 20–45 PTO hp · Y-blades only
Confirm the complete operating weight; a shipping weight cannot establish the attachment load.
Flail mowerWoodMaxx
55″ cutting width, inches · 24–45 PTO hp · Hammer blades only
Resolve the conflicting published specifications for the exact model revision.
Flail mowerWoodMaxx
55″ cutting width, inches · 24–45 PTO hp · Hammer blades only
Confirm rear remotes, hydraulic flow and pressure requirements.
Flail mowerFarmry
87″ cutting width · 30–85 HP (basis not stated) · official page and manual
Ask the manufacturer whether the horsepower range means engine or PTO power.
Flail mowerFarmer-Helper
37″ cutting width, inches · 15–45 PTO hp on the product page; manual lists the 15-PTO-hp minimum and a 45-hp gearbox
Confirm the conflicting tractor specifications in your serial-specific manual; official source values differ.
9 more possible options in the full comparison table.
THE DECISION IN NUMBERS
Numerical differences are specification comparisons only. Engine horsepower, hydraulic lift and pump flow do not increase available PTO horsepower.
Scroll the table sideways on smaller screens.
| Candidate / configuration | Published requirement | Result for this tractor scope | Decision still needed |
|---|---|---|---|
| FM54 Y · 47-inch cut | 15–25 PTO hp | Inside; 0.7 hp below the upper bound | Smaller cutting width; confirm coverage and complete load. |
| FM62 Y · 55-inch cut | 20–45 PTO hp | 4.3 hp above minimum | Grass-oriented blade choice; this is a separately configured mower. |
| FM62 hammer · 55-inch cut | 24–45 PTO hp in current manual | Only 0.3 hp above minimum | Little numerical margin; confirm intended material and exact hammer specification. |
| FM62H hammer · 55-inch cut | 24–45 PTO hp plus hydraulic side shift | Same 0.3-hp margin | Added offset function needs a verified installed rear circuit. |
| FM78 hammer · 70-inch cut | 30–65 PTO hp | 5.7 hp below minimum | Exclude from this documented power scope. |
| FM2560 hammer · 60-inch cut | 33–80 tractor hp; basis unspecified | 24.3 PTO and current 32 engine label are both below 33 | No power clearance; a 3033R badge is not a 33-hp requirement match. |
The current WoodMaxx manual separates the FM62 Y range of 20–45 PTO hp from the hammer range of 24–45. At 24.3, both enter a paper shortlist, but their margins differ sharply. The generic page headline starts at 20 and must not erase the hammer-specific 24 minimum. WoodMaxx says factory Y and hammer configurations are not interchangeable. Choose for the actual vegetation and obtain a response tied to the supplied configuration; a 0.3-hp arithmetic margin is not a prediction of mowing performance.
The fixed FM62 has no side-shift cylinder. FM62H adds that function without lowering its hammer power requirement. Deere’s book lists open-station packages 3320/3400 and 3330/3420, but has conflicting mid-PTO notes. An invoice or build sheet and the actual rear couplers must establish what is installed. The brochure’s 15.3-gpm figure is total pump flow; the separate implement reference is 9.1, and an older manual differs. Neither establishes the valve, pressure or flow suitability of the mower cylinder.
Deere’s current-linked brochure rates lift at 24 inches behind the center link. WoodMaxx’s current FM62 manual gives 774 lb generic product weight, while the page record gives 641 lb mower body and a separate 39 lb shaft. These do not establish a complete hammer or Y operating load at its actual center of gravity. Obtain the ordered configuration’s assembled mass and geometry. The Deere manual’s implement-code tables are for Deere implements with iMatch; no equivalent code is established for these mowers.
This tractor scope falls below the FM78’s stated PTO minimum. FM2560 has an unresolved engine/PTO basis, but both 24.3 PTO hp and the current 32-hp engine label fall below its 33-hp minimum. Its 965-lb manual reference is a duckfoot unit, not the complete hammer machine. Neither a larger hitch-lift figure nor a nominal model number resolves the power or weight requirement.
Farmry rates the HFS87 at 30–85 hp without saying whether that is PTO or engine power, lists Category I and II, cuts 87 inches and weighs 1,299 lb with the shaft. Its 32 engine hp is inside, but its 24.3 PTO hp is 5.7 short of 30, so the answer depends on which figure Farmry means; ask before buying. Its published lift at 24 inches, 2,200 lb, carries that weight with 901 lb to spare; check front ballast all the same. Its gearbox rating, 50 hp, is not below this tractor’s PTO power. The 87-inch cut is 3 inches wider than Land Pride’s FM2584. Farmry’s page listed it at $4,499 on November 14, 2026.
Farmer-Helper rates its standard-duty FH-EF mowers by PTO power, all to 45 PTO hp with a 45-hp gearbox: the EF95 (37-inch cut) from 15, the EF105 (41-inch) from 16 and the EF125 (48-inch) from 20. They carry Y-blades for grass and light brush. The John Deere 3033R’s 24.3 PTO hp is inside all three. Its published lift at 24 inches, 2,200 lb, carries even the 390-lb EF125 with 1,810 lb to spare. Betstco listed them at $1,462, $1,547 and $1,632 on November 14, 2026, with the PTO shaft included.
THE SCREEN, WITH ITS LIMITS VISIBLE
No pairing below is manufacturer-confirmed. “Preliminary” still requires implement limits, load center, ballast, hitch geometry and shaft checks.
Initial specification screen only. Scroll the table on small screens. Read the product page for every remaining check.
| Attachment | 1368LV U.S. document scope · 3-range eHydro · 4WD · open station / folding ROPS24.3 PTO hp |
|---|---|
| Farmry LFS45 →355 lb · Net weight WITH PTO shaft, current LFS manual Rev 1.7 p18 | Needs specification reviewAsk the manufacturer whether the horsepower range means engine or PTO power. |
| Farmry LFS53 →395 lb · Net weight WITH PTO shaft, current LFS manual Rev 1.7 p18 | Needs specification reviewAsk the manufacturer whether the horsepower range means engine or PTO power. |
| Farmry LFS61 →421 lb · Net weight WITH PTO shaft, current LFS manual Rev 1.7 p18 | Needs specification reviewAsk the manufacturer whether the horsepower range means engine or PTO power. |
| TMG Industrial TMG-TFM60 →650 lb · Product-page operation weight; manual gives conflicting 270 kg (about 595 lb) | Needs specification reviewAsk the manufacturer whether the horsepower range means engine or PTO power. |
| Farmry LFP47 →464 lb · 464 lb including PTO shaft on the product page; current Rev 1.3 manual lists 210 kg / 463.7 lb. Shipping weight is a separate 671 lb. | Needs specification reviewAsk the manufacturer whether the horsepower range means engine or PTO power. |
| TMG Industrial TFMS50 →660 lb · Product-page operation weight: 660 lb. Manual structure weight: 300 kg (about 661 lb); shaft and fluid inclusion are not explicit. Shipping weight: 770 lb. | Needs specification reviewAsk the manufacturer whether the horsepower range means engine or PTO power. |
| WoodMaxx FM-54 · Y-blades →408 lb · Current 2025-and-newer manual p40 lists 408 lb product weight without stating shaft inclusion. Page instead says 410 lb mower-only plus a 39 lb shaft. Do not treat 408 lb as a verified complete operating assembly; confirm delivered Y-blade weight. Shipping page figure is 500 lb. | Needs specification reviewResolve the conflicting published specifications for the exact model revision. |
| WoodMaxx FM-62H · Hammer blades →860 lb · Current 2025-and-newer manual, printed p40 / PDF p41: 860 lb product weight; shaft/oil/packaging inclusion is unstated. Page instead lists 716 lb mower-only plus a 39 lb shaft. Shipping is separately labeled 860 lb. Do not treat the manual number as verified complete operating weight; confirm delivered hammer assembly. | Needs specification reviewConfirm rear remotes, hydraulic flow and pressure requirements. |
| WoodMaxx FM-78H · Hammer blades →968 lb · Current 2025-and-newer manual, printed p40 / PDF p41: 968 lb product weight; shaft/oil/packaging inclusion is unstated. Page instead lists 804 lb mower-only plus a 39 lb shaft. Shipping is separately labeled 1000 lb. Do not treat the manual number as verified complete operating weight; confirm delivered hammer assembly. | Published mismatch24.3 PTO hp is below the 30 hp minimum. |
| WoodMaxx FM-62 · Hammer blades →774 lb · Current 2025-and-newer manual printed p40 / PDF p41 lists 774 lb product weight without shaft/oil/packaging inclusion. Page lists 641 lb mower-only plus a 39 lb shaft; shipping is separately labeled 800 lb. Retain these distinct bases and confirm complete operating weight for the delivered hammer assembly. | Needs specification reviewResolve the conflicting published specifications for the exact model revision. |
| WoodMaxx FM-78 · Hammer blades →880 lb · Current 2025-and-newer manual printed p40 / PDF p41 lists 880 lb product weight without shaft/oil/packaging inclusion. Page lists 710 lb mower-only plus a 39 lb shaft; shipping is separately labeled 900 lb. Retain these distinct bases and confirm complete operating weight for the delivered hammer assembly. | Published mismatch24.3 PTO hp is below the 30 hp minimum. |
| Farmer-Helper FH-EFGC125 · Hammer blades →Operating weight unconfirmed · Complete operating weight is unverified. Current page: 576 lb “Weight” and 624 lb “Crated Weight.” Linked Rev 12-12-17 manual p23: 600 lb “Weight” and 635 lb crated. Product-weight shaft/oil/assembly inclusions are unstated. Keep these separate; do not use crate weight or silently choose one product figure as an operating load. | Needs specification reviewConfirm the complete operating weight; a shipping weight cannot establish the attachment load. |
| Farmer-Helper FH-EFGC155 · Hammer blades →Operating weight unconfirmed · Complete operating weight is unverified. Current page: 741 lb “Weight” and 789 lb “Crated Weight.” Linked Rev 12-12-17 manual p23: 720 lb “Weight” and 755 lb crated. Product-weight shaft/oil/assembly inclusions are unstated. Keep these separate; do not use crate weight or silently choose one product figure as an operating load. | Published mismatch24.3 PTO hp is below the 25 hp minimum. |
| WoodMaxx FM-62 · Y-blades →Operating weight unconfirmed · Complete Y-configuration operating weight is unverified. Current manual p40 gives 774 lb generic product weight without shaft/oil or blade-specific inclusion. Page gives 641 lb mower-only plus 39 lb shaft and separately 800 lb shipping. These bases conflict or lack scope; none substitutes for an assembled Y operating load. | Needs specification reviewConfirm the complete operating weight; a shipping weight cannot establish the attachment load. |
| WoodMaxx FM-78 · Y-blades →Operating weight unconfirmed · Complete Y-configuration operating weight is unverified. Current manual p40 gives 880 lb generic product weight without shaft/oil or blade-specific inclusion. Page gives 710 lb mower-only plus 39 lb shaft and separately 900 lb shipping. These bases conflict or lack scope; none substitutes for an assembled Y operating load. | Published mismatch24.3 PTO hp is below the 30 hp minimum. |
| Land Pride FM2560 · hammer rotor →Operating weight unconfirmed · Manual p39 specifies 965 lb for the standard unit with a duckfoot rotor; the brochure lists 929 lb without a rotor/inclusion basis. The separate hammer-rotor assembly is 222 lb. No complete hammer operating mass or shipping mass is established. Do not add the rotor to an already rotor-inclusive unit weight or substitute these references for the operating load. | Published mismatchBoth engine (32) and PTO (24.3) horsepower are below the published 33 hp minimum. |
| Land Pride FM2572 · hammer rotor →Operating weight unconfirmed · Manual p39 specifies 1,040 lb for the standard unit with a duckfoot rotor; the brochure lists 1,040 lb without a rotor/inclusion basis. The separate hammer-rotor assembly is 261 lb. No complete hammer operating mass or shipping mass is established. Do not add the rotor to an already rotor-inclusive unit weight or substitute these references for the operating load. | Published mismatchBoth engine (32) and PTO (24.3) horsepower are below the published 42 hp minimum. |
| Land Pride FM2584 · hammer rotor →Operating weight unconfirmed · Manual p39 specifies 1,236 lb for the standard unit with a duckfoot rotor; the brochure lists 1,168 lb without a rotor/inclusion basis. The separate hammer-rotor assembly is 301 lb. No complete hammer operating mass or shipping mass is established. Do not add the rotor to an already rotor-inclusive unit weight or substitute these references for the operating load. | Published mismatchBoth engine (32) and PTO (24.3) horsepower are below the published 49 hp minimum. |
| Blue Diamond Heavy Duty 403740 →1763 lb · 1,763 lb (800 kg) in the Aug-2025 spec sheet (without PTO) and the Feb-2026 manual p49. Add the PTO shaft for the operating load. | Published mismatchBoth engine (32) and PTO (24.3) horsepower are below the published 75 hp minimum. |
| Farmry HFS87 →1299 lb · 1,299 lb (589 kg) including PTO shaft on the product page and in the HFS manual Rev 1.6, printed p17. | Needs specification reviewAsk the manufacturer whether the horsepower range means engine or PTO power. |
| Farmer-Helper FH-EF95 →330 lb · 330 lb retained, the heavier of the product page (325 lb) and the FH-EF manual p13 (330 lb); crated 360 lb. Neither says whether the included PTO shaft is counted. | Needs specification reviewConfirm the conflicting tractor specifications in your serial-specific manual; official source values differ. |
| Farmer-Helper FH-EF105 →347 lb · 347 lb retained, the heavier of the product page (342 lb) and the FH-EF manual p13 (347 lb); crated 377 lb. Neither says whether the included PTO shaft is counted. | Needs specification reviewConfirm the conflicting tractor specifications in your serial-specific manual; official source values differ. |
| Farmer-Helper FH-EF125 →390 lb · 390 lb retained, the heavier of the product page (390 lb) and the FH-EF manual p13 (383 lb); crated 438 lb. Neither says whether the included PTO shaft is counted. | Needs specification reviewConfirm the conflicting tractor specifications in your serial-specific manual; official source values differ. |
Does my power and material call for the FM-62 Y order or the higher-minimum hammer configuration?
Read the guide →FIELD GUIDETake the complete setup, not just a horsepower number, to the manufacturer.
Read the guide →FOLLOW THE NUMBERS
Research record reviewed November 8, 2026. Confirm the current manual and the exact revision supplied with your machine.