Kubota L2502 · PTO WOOD CHIPPERS
The L2502’s source revision changes a borderline chipper decision. Current Kubota material gives 18.4 PTO hp for HST and 19.8 for gear, both below the WC68’s 20 hp minimum. An older official sheet lists 19.0 and 20.5. Confirm the rating that applies to your serial number before using the older gear figure to create a match.
By Acreage Equipment · Reviewed November 7, 2026 · Specification research, not a field test
PUT THIS GUIDE TO WORK
See published mismatches and the checks still needed.
BEST MATCHES FOR THE L2502
9 of 19 pto wood chippers we track pass the published power, hitch and speed screen on at least one configuration. Each still has a detail to confirm with the seller.
PTO chipperFarmer-Helper
4″ published feed-capacity short side, inches · 15–45 PTO hp in current index-linked manual; older/page conflicts retained
Confirm the complete operating weight; a shipping weight cannot establish the attachment load.
PTO chipperFarmry
5″ max. chip diameter · 15–45 engine hp
Confirm the conflicting tractor specifications in your serial-specific manual; official source values differ.
PTO chipperFarmry
5″ max. chip diameter · 15–45 PTO hp
Resolve the conflicting published specifications for the exact model revision.
PTO chipperWoodland Mills
5″ max. chip diameter · 12–30 PTO hp in table; manual hitch paragraph says 15–30 — resolve before selection
Resolve the conflicting published specifications for the exact model revision.
PTO chipperWoodland Mills
4″ max. chip diameter · 15–30 PTO hp
Confirm the conflicting tractor specifications in your serial-specific manual; official source values differ.
PTO chipperWoodMaxx
8″ max. chip diameter · 19 PTO hp minimum; maximum not stated
18.4 PTO hp is below the 19 hp minimum.
3 more possible options in the full comparison table.
THE DECISION IN NUMBERS
WC68 starts at 20 PTO hp. These are conditional power checks, not approved pairings. No serial-number transition between the Kubota sources has been verified.
Scroll the table sideways on smaller screens.
| L2502 configuration | Current source | Older linked sheet | Effect on the 20 hp minimum |
|---|---|---|---|
| HST | 18.4 PTO hp | 19.0 PTO hp | Below under both sources |
| Gear | 19.8 PTO hp | 20.5 PTO hp | Current: below. Older: clears the minimum only. |
The current 19.8 PTO-hp gear figure misses WC68’s 20 minimum; the older 20.5 figure clears that one requirement. No verified production-year breakpoint has been established in this research. We use current published ratings for initial screening and keep the alternative source visible, rather than labeling every L2502 gear tractor as compatible.
Both 18.4 and 19.0 PTO hp are below 20. The source conflict matters to documenting the tractor, but it does not reverse this particular result. WC46’s 15–30 PTO-hp band includes both HST figures, although neither reaches the maker’s over-20-PTO-hp condition for full four-inch logs at full feed speed.
Even the older gear figure is far below the over-40-PTO-hp condition for full six-inch logs at full feed speed. WC68 also has a 747 lb listed product weight versus WC46’s 587 lb. Ask whether the larger throat solves your actual branch-shape problem, then confirm load center, ballast and driveline setup separately.
THE SCREEN, WITH ITS LIMITS VISIBLE
No pairing below is manufacturer-confirmed. “Preliminary” still requires implement limits, load center, ballast, hitch geometry and shaft checks.
Initial specification screen only. Scroll the table on small screens. Read the product page for every remaining check.
| Attachment | HST · 4WD18.4 PTO hp | Gear · 2WD / 4WD19.8 PTO hp |
|---|---|---|
| Farmry WCAP5 →412 lb · Net weight WITH PTO shaft, manual Rev1.5 p20 | Needs specification reviewConfirm the conflicting tractor specifications in your serial-specific manual; official source values differ. | Needs specification reviewConfirm the conflicting tractor specifications in your serial-specific manual; official source values differ. |
| Farmry WCAP5 PRO →386 lb · Product weight, current manual Rev1.4 p13; whether PTO shaft is included in this weight is not stated | Needs specification reviewResolve the conflicting published specifications for the exact model revision. | Needs specification reviewResolve the conflicting published specifications for the exact model revision. |
| Woodland Mills WC46 →587 lb · Product weight, 2024 operator manual Rev C p9 | Needs specification reviewConfirm the conflicting tractor specifications in your serial-specific manual; official source values differ. | Needs specification reviewConfirm the conflicting tractor specifications in your serial-specific manual; official source values differ. |
| Woodland Mills WC68 →747 lb · Product weight, 2024 operator manual Rev C p9 | Published mismatch18.4 PTO hp is below the 20 hp minimum. | Published mismatch19.8 PTO hp is below the 20 hp minimum. |
| Woodland Mills TFG55 PTO →346 lb · Product weight, Rev B manual p9 | Needs specification reviewResolve the conflicting published specifications for the exact model revision. | Needs specification reviewResolve the conflicting published specifications for the exact model revision. |
| Woodland Mills WC88 →900 lb · Product weight: 900 lb in current linked 2022 Rev C manual, printed p9; shipping weight is 1,054 lb. The manual does not explicitly identify whether quoted product weight includes the PTO shaft or filled hydraulic oil. | Published mismatch18.4 PTO hp is below the 35 hp minimum. | Published mismatch19.8 PTO hp is below the 35 hp minimum. |
| WoodMaxx WM-8H →Operating weight unconfirmed · Operating weight is unverified in the current official product page and linked manual. The page lists 990 lb SHIPPING weight; do not use it as operating weight. Confirm weight with PTO shaft and a filled hydraulic tank. | Published mismatch18.4 PTO hp is below the 19 hp minimum. | Needs specification reviewConfirm the complete operating weight; a shipping weight cannot establish the attachment load. |
| WoodMaxx WM-8M →775 lb · Product page states 775 lb total weight on the three-point hitch; shaft/fluid inclusion is not explicit. Shipping sections conflict at 950 versus 990 lb. Confirm the delivered operating assembly and shipping revision. | Published mismatch18.4 PTO hp is below the 19 hp minimum. | Needs specification reviewResolve the conflicting published specifications for the exact model revision. |
| WoodMaxx MX-8800 →Operating weight unconfirmed · Complete operating weight is unverified. Current Rev D manual (printed p45 / pdf p46, technical specifications) states approximately 772 lb DRY weight; page separately states 1,004 lb SHIPPING weight. Shaft inclusion in dry weight is not explicit. Do not substitute either figure for a confirmed shaft/oil-inclusive operating load. | Published mismatch18.4 PTO hp is below the 20 hp minimum. | Published mismatch19.8 PTO hp is below the 20 hp minimum. |
| WoodMaxx MX-9900 →Operating weight unconfirmed · Complete operating weight is unverified. Current Rev C manual (printed p42 / pdf p43, technical specifications) states approximately 816 lb DRY weight; page separately states 1,048 lb SHIPPING weight. Shaft inclusion in dry weight is not explicit. Do not substitute either figure for a confirmed shaft/oil-inclusive operating load. | Published mismatch18.4 PTO hp is below the 25 hp minimum. | Published mismatch19.8 PTO hp is below the 25 hp minimum. |
| Farmer-Helper FH-BX42 →Operating weight unconfirmed · Complete operating weight is unverified. Current index-linked manual p2 lists 430 lb net and 450 lb shipping. Current product/series pages instead list 423 lb net and 458 lb shipping. Net-weight shaft/assembly inclusions are unstated; none is substituted for a verified operating load. | Needs specification reviewConfirm the complete operating weight; a shipping weight cannot establish the attachment load. | Needs specification reviewConfirm the complete operating weight; a shipping weight cannot establish the attachment load. |
| Farmer-Helper FH-BX62S →Operating weight unconfirmed · Complete operating weight is unverified. Current index-linked manual p2: 830 lb net / 860 lb shipping. Current series page: 835 lb net / 915 lb gross. Product page calls 835 lb both total and gross; older product-linked manual p38 gives 797 lb net / 850 lb gross. Shaft/assembly inclusions are unstated, so no reference is used as operating weight. | Published mismatch18.4 PTO hp is below the 25 hp minimum. | Published mismatch19.8 PTO hp is below the 25 hp minimum. |
| Wallenstein BX36S →Operating weight unconfirmed · Official page Total Weight and Jan-2025 manual Weight: 395 lb. Neither states whether the supplied shaft and all operating equipment are included; complete operating and separate shipping weights remain unverified. | Needs specification reviewConfirm the correct attachment and driveline configuration for the tractor’s PTO speed; listed speed options are discrete settings. | Needs specification reviewConfirm the correct attachment and driveline configuration for the tractor’s PTO speed; listed speed options are discrete settings. |
| Wallenstein BX52S →Operating weight unconfirmed · Official page Total Weight and Jan-2025 manual Weight: 505 lb. Neither states whether the supplied shaft and all operating equipment are included; complete operating and separate shipping weights remain unverified. | Needs specification reviewConfirm the correct attachment and driveline configuration for the tractor’s PTO speed; listed speed options are discrete settings. | Needs specification reviewConfirm the correct attachment and driveline configuration for the tractor’s PTO speed; listed speed options are discrete settings. |
| Wallenstein BX72S →Operating weight unconfirmed · Current official page Total Weight and Jan-2025 manual Weight: 728 lb. Neither defines complete shaft-inclusive operating mass or a separate shipping weight. Confirm the assembled operating load; do not relabel 728 lb as dry or shipping weight. | Published mismatch23.3 engine hp is below the 50 hp minimum. | Published mismatch23.3 engine hp is below the 50 hp minimum. |
| Wallenstein BX102S →1143 lb · Total Weight 1143 lb (519 kg) on the current page and in the Jan-2025 BX-S manual. Neither says whether the PTO shaft is included; confirm the assembled operating load. | Published mismatch23.3 engine hp is below the 80 hp minimum. | Published mismatch23.3 engine hp is below the 80 hp minimum. |
| Wallenstein BX52RI →845 lb · Total weight 845 lb on the current page and operating weight 845 lb in the BXR manual §10.1. Neither says whether the PTO shaft is included. | Published mismatch23.3 engine hp is below the 30 hp minimum. | Published mismatch23.3 engine hp is below the 30 hp minimum. |
| Wallenstein BX72RI →1300 lb · Total weight 1,300 lb on the current page and operating weight 1,300 lb in the BXR manual §10.1. Neither says whether the PTO shaft is included. | Published mismatch23.3 engine hp is below the 45 hp minimum. | Published mismatch23.3 engine hp is below the 45 hp minimum. |
| Wallenstein BX102RI →1950 lb · Total weight 1,950 lb on the current page and operating weight 1,950 lb in the BXR manual §10.1. Neither says whether the PTO shaft is included. | Published mismatch23.3 engine hp is below the 75 hp minimum. | Published mismatch23.3 engine hp is below the 75 hp minimum. |
Should I buy the WC46 or WC68 when my compact tractor is near 20 PTO hp?
Read the guide →FIELD GUIDETake the complete setup, not just a horsepower number, to the manufacturer.
Read the guide →FOLLOW THE NUMBERS
Research record reviewed November 7, 2026. Confirm the current manual and the exact revision supplied with your machine.