TYM T5074 · PTO WOOD CHIPPERS
Wallenstein lists BX72S for 50–85 engine hp and Category I and II, and the TYM T5074’s 71.5 hp and Category II hitch sit inside both. WoodMaxx’s four chippers fit too; the Category 1-only chippers such as WC88 do not.
By Acreage Equipment · Reviewed November 14, 2026 · Specification research, not a field test
PUT THIS GUIDE TO WORK
See published mismatches and the checks still needed.
BEST MATCHES FOR THE T5074
6 of 19 pto wood chippers we track pass the published power, hitch and speed screen. Each still has a detail to confirm with the seller.
PTO chipperWallenstein
7″ max. chip diameter · 50–85 engine hp · official U.S. page
Confirm the correct attachment and driveline configuration for the tractor’s PTO speed; listed speed options are discrete settings.
PTO chipperWoodMaxx
8″ max. chip diameter · 19 PTO hp minimum; maximum not stated
Resolve the conflicting published specifications for the exact model revision.
PTO chipperWoodMaxx
9″ maximum chip diameter, inches · 25 PTO hp minimum; maximum not stated
Confirm the complete operating weight; a shipping weight cannot establish the attachment load.
PTO chipperWoodMaxx
8″ maximum chip diameter, inches · 20 PTO hp minimum; maximum not stated
Confirm the complete operating weight; a shipping weight cannot establish the attachment load.
PTO chipperWoodMaxx
8″ max. chip diameter · 19 PTO hp minimum; maximum not stated
Confirm the complete operating weight; a shipping weight cannot establish the attachment load.
PTO chipperWallenstein
7″ max. chip diameter · 45–85 engine hp · current U.S. page (manual table: 50–85 hp for the BX72R)
Confirm the correct attachment and driveline configuration for the tractor’s PTO speed; listed speed options are discrete settings.
THE DECISION IN NUMBERS
Tractor reference: TYM T5074 (ROPS, power shuttle), February 2026 Series 5 brochure; Category II; 3,159 lb at 24 in.
Scroll the table sideways on smaller screens.
| Chipper | Published requirement | On 60.2 PTO / 71.5 engine hp | Result |
|---|---|---|---|
| WoodMaxx MX-9900 / MX-8800 / WM-8M / WM-8H | 19–25 PTO hp minimum; 50+ for full capacity; Category 1/2 | Inside; 10.2 over the 50+ line | Fits |
| Wallenstein BX72S | 50–85 engine hp; Category I and II | Inside (13.5 under) | Fits |
| Woodland Mills WC88 | 35 PTO hp minimum; Category 1 | Power inside; hitch mismatch | Excluded |
| Wallenstein BX72RI | 45–85 engine hp (page); hydraulic feed; 7-in. | BX72RI inside | Fits on page and manual; hydraulic remote or power pack |
| Woodland Mills WC68 | 20–50 PTO hp; Category 1 | Over and hitch mismatch | Excluded |
| All other chippers here | To 55 hp or less | Over | Excluded |
Wallenstein BX72S (7-inch) has a published 85-hp ceiling; WoodMaxx WM-8M (8-inch, mechanical feed) lists 19 PTO hp minimum and 50+ for full capacity, with no maximum. The T5074 fits both. The comparison below sets them side by side.
Woodland Mills WC88 needs 35 PTO hp, which the T5074 clears, and its over-60 full-feed line is just 0.2 above the tractor. But WC88 lists Category 1 only, so it would need a conversion approved in writing; this site screens it out.
TYM lists the Series 5 hitch as Category II. Category 1-only attachments such as Woodland Mills WC88, Land Pride FM2560 and the Farmer-Helper mowers would need bushings or a quick hitch approved in writing; this site screens them out.
TYM’s 2026 brochure lists 3,159 lb 24 inches behind the link ends (4,329 lb at the ends). WoodMaxx FM-78H, the heaviest attachment here at 968 lb, is well under it; check the quoted attachment’s weight with its shaft and the front ballast the dealer recommends.
Wallenstein’s current pages rate the 7-inch BX72RI (45–85 engine hp, Category I and II). Two hydraulic rollers pull material in at a set rate, and P3 PULSE reverses them when the rotor slows; they need 3–6 gpm from a rear remote or Wallenstein’s PTO-driven power pack. The TYM T5074’s 71.5 engine hp is inside the BX72RI’s range on both the page and the manual. Its published lift at 24 inches, 3,159 lb, carries the 1,300-lb BX72RI with 1,859 lb to spare. Wallenstein lists no price; ask a dealer.
THE SCREEN, WITH ITS LIMITS VISIBLE
No pairing below is manufacturer-confirmed. “Preliminary” still requires implement limits, load center, ballast, hitch geometry and shaft checks.
Initial specification screen only. Scroll the table on small screens. Read the product page for every remaining check.
| Attachment | U.S. T5074 · 12F/12R power shuttle · 4WD · ROPS · independent PTO60.2 PTO hp |
|---|---|
| Farmry WCAP5 →412 lb · Net weight WITH PTO shaft, manual Rev1.5 p20 | Published mismatch71.5 engine hp exceeds the published 45 hp range. |
| Farmry WCAP5 PRO →386 lb · Product weight, current manual Rev1.4 p13; whether PTO shaft is included in this weight is not stated | Published mismatch60.2 PTO hp exceeds the published 45 hp range. |
| Woodland Mills WC46 →587 lb · Product weight, 2024 operator manual Rev C p9 | Published mismatch60.2 PTO hp exceeds the published 30 hp range. |
| Woodland Mills WC68 →747 lb · Product weight, 2024 operator manual Rev C p9 | Published mismatch60.2 PTO hp exceeds the published 50 hp range. |
| Woodland Mills TFG55 PTO →346 lb · Product weight, Rev B manual p9 | Published mismatch60.2 PTO hp exceeds the published 30 hp range. |
| Woodland Mills WC88 →900 lb · Product weight: 900 lb in current linked 2022 Rev C manual, printed p9; shipping weight is 1,054 lb. The manual does not explicitly identify whether quoted product weight includes the PTO shaft or filled hydraulic oil. | Published mismatchThe attachment’s listed hitch categories do not overlap the tractor’s documented Category 2 interface. |
| WoodMaxx WM-8H →Operating weight unconfirmed · Operating weight is unverified in the current official product page and linked manual. The page lists 990 lb SHIPPING weight; do not use it as operating weight. Confirm weight with PTO shaft and a filled hydraulic tank. | Needs specification reviewConfirm the complete operating weight; a shipping weight cannot establish the attachment load. |
| WoodMaxx WM-8M →775 lb · Product page states 775 lb total weight on the three-point hitch; shaft/fluid inclusion is not explicit. Shipping sections conflict at 950 versus 990 lb. Confirm the delivered operating assembly and shipping revision. | Needs specification reviewResolve the conflicting published specifications for the exact model revision. |
| WoodMaxx MX-8800 →Operating weight unconfirmed · Complete operating weight is unverified. Current Rev D manual (printed p45 / pdf p46, technical specifications) states approximately 772 lb DRY weight; page separately states 1,004 lb SHIPPING weight. Shaft inclusion in dry weight is not explicit. Do not substitute either figure for a confirmed shaft/oil-inclusive operating load. | Needs specification reviewConfirm the complete operating weight; a shipping weight cannot establish the attachment load. |
| WoodMaxx MX-9900 →Operating weight unconfirmed · Complete operating weight is unverified. Current Rev C manual (printed p42 / pdf p43, technical specifications) states approximately 816 lb DRY weight; page separately states 1,048 lb SHIPPING weight. Shaft inclusion in dry weight is not explicit. Do not substitute either figure for a confirmed shaft/oil-inclusive operating load. | Needs specification reviewConfirm the complete operating weight; a shipping weight cannot establish the attachment load. |
| Farmer-Helper FH-BX42 →Operating weight unconfirmed · Complete operating weight is unverified. Current index-linked manual p2 lists 430 lb net and 450 lb shipping. Current product/series pages instead list 423 lb net and 458 lb shipping. Net-weight shaft/assembly inclusions are unstated; none is substituted for a verified operating load. | Published mismatch60.2 PTO hp exceeds the published 45 hp range. |
| Farmer-Helper FH-BX62S →Operating weight unconfirmed · Complete operating weight is unverified. Current index-linked manual p2: 830 lb net / 860 lb shipping. Current series page: 835 lb net / 915 lb gross. Product page calls 835 lb both total and gross; older product-linked manual p38 gives 797 lb net / 850 lb gross. Shaft/assembly inclusions are unstated, so no reference is used as operating weight. | Published mismatch60.2 PTO hp exceeds the published 45 hp range. |
| Wallenstein BX36S →Operating weight unconfirmed · Official page Total Weight and Jan-2025 manual Weight: 395 lb. Neither states whether the supplied shaft and all operating equipment are included; complete operating and separate shipping weights remain unverified. | Published mismatch71.5 engine hp exceeds the published 30 hp range. |
| Wallenstein BX52S →Operating weight unconfirmed · Official page Total Weight and Jan-2025 manual Weight: 505 lb. Neither states whether the supplied shaft and all operating equipment are included; complete operating and separate shipping weights remain unverified. | Published mismatch71.5 engine hp exceeds the published 55 hp range. |
| Wallenstein BX72S →Operating weight unconfirmed · Current official page Total Weight and Jan-2025 manual Weight: 728 lb. Neither defines complete shaft-inclusive operating mass or a separate shipping weight. Confirm the assembled operating load; do not relabel 728 lb as dry or shipping weight. | Needs specification reviewConfirm the correct attachment and driveline configuration for the tractor’s PTO speed; listed speed options are discrete settings. |
| Wallenstein BX102S →1143 lb · Total Weight 1143 lb (519 kg) on the current page and in the Jan-2025 BX-S manual. Neither says whether the PTO shaft is included; confirm the assembled operating load. | Published mismatch71.5 engine hp is below the 80 hp minimum. |
| Wallenstein BX52RI →845 lb · Total weight 845 lb on the current page and operating weight 845 lb in the BXR manual §10.1. Neither says whether the PTO shaft is included. | Published mismatch71.5 engine hp exceeds the published 55 hp range. |
| Wallenstein BX72RI →1300 lb · Total weight 1,300 lb on the current page and operating weight 1,300 lb in the BXR manual §10.1. Neither says whether the PTO shaft is included. | Needs specification reviewConfirm the correct attachment and driveline configuration for the tractor’s PTO speed; listed speed options are discrete settings. |
| Wallenstein BX102RI →1950 lb · Total weight 1,950 lb on the current page and operating weight 1,950 lb in the BXR manual §10.1. Neither says whether the PTO shaft is included. | Published mismatch71.5 engine hp is below the 75 hp minimum. |
On a Category 2 tractor with about 52 engine and 42–44 PTO hp, is BX72S or WM-8M the better chipper?
Read the guide →FIELD GUIDETake the complete setup, not just a horsepower number, to the manufacturer.
Read the guide →FOLLOW THE NUMBERS
Research record reviewed November 14, 2026. Confirm the current manual and the exact revision supplied with your machine.