KIOTI DK5020 · PTO WOOD CHIPPERS
DK5020’s 41.5 PTO hp exceeds WC68’s over 40 hp condition for full six-inch material at full feed speed. Do not transfer that result to the 50.3 engine-hp DK5320SEH, which has 39.3 PTO hp. A WC88 still introduces a higher power condition and heavier implement rather than an automatic upgrade.
By Acreage Equipment · Reviewed November 7, 2026 · Specification research, not a field test
PUT THIS GUIDE TO WORK
See published mismatches and the checks still needed.
BEST MATCHES FOR THE DK5020
13 of 19 pto wood chippers we track pass the published power, hitch and speed screen. Each still has a detail to confirm with the seller.
PTO chipperWoodland Mills
6″ max. chip diameter · 20–50 PTO hp
Confirm the conflicting tractor specifications in your serial-specific manual; official source values differ.
PTO chipperWoodland Mills
8″ maximum branch diameter, inches · 35–100+ PTO hp
Resolve the conflicting published specifications for the exact model revision.
PTO chipperWallenstein
5″ max. chip diameter · 30–55 engine hp · current U.S. page (manual table: 40–55 hp for the BX52R)
Confirm the correct attachment and driveline configuration for the tractor’s PTO speed; listed speed options are discrete settings.
PTO chipperWallenstein
7″ max. chip diameter · 45–85 engine hp · current U.S. page (manual table: 50–85 hp for the BX72R)
Confirm the correct attachment and driveline configuration for the tractor’s PTO speed; listed speed options are discrete settings.
PTO chipperFarmer-Helper
4″ published feed-capacity short side, inches · 15–45 PTO hp in current index-linked manual; older/page conflicts retained
Confirm the complete operating weight; a shipping weight cannot establish the attachment load.
PTO chipperFarmry
5″ max. chip diameter · 15–45 PTO hp
Resolve the conflicting published specifications for the exact model revision.
7 more possible options in the full comparison table.
THE DECISION IN NUMBERS
Compare exact model/transmission outputs. These published conditions do not promise measured throughput or approve a tractor–chipper pairing.
Scroll the table sideways on smaller screens.
| Condition | DK5020 manual: 41.5 PTO hp | DK5320SEH HST: 39.3 PTO hp |
|---|---|---|
| WC68 operating band: 20–50 PTO hp | Inside | Inside |
| WC68 full 6 in/full feed: over 40 PTO hp | Above 40 by 1.5 hp | Below 40 by 0.7 hp |
| WC88 minimum: 35 PTO hp | Above by 6.5 hp | Above by 4.3 hp |
| WC88 full 8 in/full feed: over 60 PTO hp | Condition not met | Condition not met |
The DK5020 manual and DK5320SEH HST both publish 50.3 gross engine hp. Their 41.5 versus 39.3 PTO ratings land on opposite sides of WC68’s over 40 full-feed condition. Confirm the exact model on the tractor rather than extending a result across the DK series. The WC68’s 20–50 PTO operating band includes both.
WC88’s 35 PTO-hp minimum is met, but its over 60 full-eight-inch/full-feed condition is not. WC88’s 900 lb retained product weight is 153 lb above WC68’s 747 lb; complete operating inclusions for WC88 remain unresolved. The 2,716 lb hitch rating at 24 in cannot by itself approve the heavier machine or its farther load center.
WCAP5 explicitly publishes 15–45 engine hp. DK5020’s 50.3 exceeds that ceiling even though its 41.5 PTO output is below 45. Do not relabel this engine requirement as PTO power to keep a lighter product on the shortlist. Resolve each chipper’s stated power basis before evaluating its feed system or carrying weight.
Wallenstein’s current pages rate the 5-inch BX52RI (30–55 engine hp, Category I) and the 7-inch BX72RI (45–85 engine hp, Category I and II). Two hydraulic rollers pull material in at a set rate, and P3 PULSE reverses them when the rotor slows; they need 3–6 gpm from a rear remote or Wallenstein’s PTO-driven power pack. The KIOTI DK5020’s 50.3 engine hp is inside the BX52RI’s range on both the page and the manual. It is inside the BX72RI’s range on both the page and the manual. Its published lift at 24 inches, 2,716 lb, carries the 1,300-lb BX72RI with 1,416 lb to spare. Wallenstein lists no price; ask a dealer.
THE SCREEN, WITH ITS LIMITS VISIBLE
No pairing below is manufacturer-confirmed. “Preliminary” still requires implement limits, load center, ballast, hitch geometry and shaft checks.
Initial specification screen only. Scroll the table on small screens. Read the product page for every remaining check.
| Attachment | Synchronized shuttle · 8F/8R · 4 WD · ROPS41.5 PTO hp |
|---|---|
| Farmry WCAP5 →412 lb · Net weight WITH PTO shaft, manual Rev1.5 p20 | Published mismatch50.3 engine hp exceeds the published 45 hp range. |
| Farmry WCAP5 PRO →386 lb · Product weight, current manual Rev1.4 p13; whether PTO shaft is included in this weight is not stated | Needs specification reviewResolve the conflicting published specifications for the exact model revision. |
| Woodland Mills WC46 →587 lb · Product weight, 2024 operator manual Rev C p9 | Published mismatch41.5 PTO hp exceeds the published 30 hp range. |
| Woodland Mills WC68 →747 lb · Product weight, 2024 operator manual Rev C p9 | Needs specification reviewConfirm the conflicting tractor specifications in your serial-specific manual; official source values differ. |
| Woodland Mills TFG55 PTO →346 lb · Product weight, Rev B manual p9 | Published mismatch41.5 PTO hp exceeds the published 30 hp range. |
| Woodland Mills WC88 →900 lb · Product weight: 900 lb in current linked 2022 Rev C manual, printed p9; shipping weight is 1,054 lb. The manual does not explicitly identify whether quoted product weight includes the PTO shaft or filled hydraulic oil. | Needs specification reviewResolve the conflicting published specifications for the exact model revision. |
| WoodMaxx WM-8H →Operating weight unconfirmed · Operating weight is unverified in the current official product page and linked manual. The page lists 990 lb SHIPPING weight; do not use it as operating weight. Confirm weight with PTO shaft and a filled hydraulic tank. | Needs specification reviewConfirm the complete operating weight; a shipping weight cannot establish the attachment load. |
| WoodMaxx WM-8M →775 lb · Product page states 775 lb total weight on the three-point hitch; shaft/fluid inclusion is not explicit. Shipping sections conflict at 950 versus 990 lb. Confirm the delivered operating assembly and shipping revision. | Needs specification reviewResolve the conflicting published specifications for the exact model revision. |
| WoodMaxx MX-8800 →Operating weight unconfirmed · Complete operating weight is unverified. Current Rev D manual (printed p45 / pdf p46, technical specifications) states approximately 772 lb DRY weight; page separately states 1,004 lb SHIPPING weight. Shaft inclusion in dry weight is not explicit. Do not substitute either figure for a confirmed shaft/oil-inclusive operating load. | Needs specification reviewConfirm the complete operating weight; a shipping weight cannot establish the attachment load. |
| WoodMaxx MX-9900 →Operating weight unconfirmed · Complete operating weight is unverified. Current Rev C manual (printed p42 / pdf p43, technical specifications) states approximately 816 lb DRY weight; page separately states 1,048 lb SHIPPING weight. Shaft inclusion in dry weight is not explicit. Do not substitute either figure for a confirmed shaft/oil-inclusive operating load. | Needs specification reviewConfirm the complete operating weight; a shipping weight cannot establish the attachment load. |
| Farmer-Helper FH-BX42 →Operating weight unconfirmed · Complete operating weight is unverified. Current index-linked manual p2 lists 430 lb net and 450 lb shipping. Current product/series pages instead list 423 lb net and 458 lb shipping. Net-weight shaft/assembly inclusions are unstated; none is substituted for a verified operating load. | Needs specification reviewConfirm the complete operating weight; a shipping weight cannot establish the attachment load. |
| Farmer-Helper FH-BX62S →Operating weight unconfirmed · Complete operating weight is unverified. Current index-linked manual p2: 830 lb net / 860 lb shipping. Current series page: 835 lb net / 915 lb gross. Product page calls 835 lb both total and gross; older product-linked manual p38 gives 797 lb net / 850 lb gross. Shaft/assembly inclusions are unstated, so no reference is used as operating weight. | Needs specification reviewConfirm the complete operating weight; a shipping weight cannot establish the attachment load. |
| Wallenstein BX36S →Operating weight unconfirmed · Official page Total Weight and Jan-2025 manual Weight: 395 lb. Neither states whether the supplied shaft and all operating equipment are included; complete operating and separate shipping weights remain unverified. | Published mismatch50.3 engine hp exceeds the published 30 hp range. |
| Wallenstein BX52S →Operating weight unconfirmed · Official page Total Weight and Jan-2025 manual Weight: 505 lb. Neither states whether the supplied shaft and all operating equipment are included; complete operating and separate shipping weights remain unverified. | Needs specification reviewConfirm the correct attachment and driveline configuration for the tractor’s PTO speed; listed speed options are discrete settings. |
| Wallenstein BX72S →Operating weight unconfirmed · Current official page Total Weight and Jan-2025 manual Weight: 728 lb. Neither defines complete shaft-inclusive operating mass or a separate shipping weight. Confirm the assembled operating load; do not relabel 728 lb as dry or shipping weight. | Needs specification reviewConfirm the correct attachment and driveline configuration for the tractor’s PTO speed; listed speed options are discrete settings. |
| Wallenstein BX102S →1143 lb · Total Weight 1143 lb (519 kg) on the current page and in the Jan-2025 BX-S manual. Neither says whether the PTO shaft is included; confirm the assembled operating load. | Published mismatch50.3 engine hp is below the 80 hp minimum. |
| Wallenstein BX52RI →845 lb · Total weight 845 lb on the current page and operating weight 845 lb in the BXR manual §10.1. Neither says whether the PTO shaft is included. | Needs specification reviewConfirm the correct attachment and driveline configuration for the tractor’s PTO speed; listed speed options are discrete settings. |
| Wallenstein BX72RI →1300 lb · Total weight 1,300 lb on the current page and operating weight 1,300 lb in the BXR manual §10.1. Neither says whether the PTO shaft is included. | Needs specification reviewConfirm the correct attachment and driveline configuration for the tractor’s PTO speed; listed speed options are discrete settings. |
| Wallenstein BX102RI →1950 lb · Total weight 1,950 lb on the current page and operating weight 1,950 lb in the BXR manual §10.1. Neither says whether the PTO shaft is included. | Published mismatch50.3 engine hp is below the 75 hp minimum. |
Is the WC88’s larger throat useful enough to justify its power and weight requirements?
Read the guide →FIELD GUIDETake the complete setup, not just a horsepower number, to the manufacturer.
Read the guide →FOLLOW THE NUMBERS
Research record reviewed November 7, 2026. Confirm the current manual and the exact revision supplied with your machine.