New Holland WORKMASTER 35 · PTO WOOD CHIPPERS
The WORKMASTER 35’s unresolved 29.7 brochure versus 27.4 observed manual PTO rating changes the numerical distance from a chipper limit, even when the initial result stays the same. Both figures fit WC46’s 15–30 band and clear WC68’s 20 minimum. They do not establish full 6-inch performance or justify choosing a larger machine solely for its advertised opening.
By Acreage Equipment · Reviewed November 7, 2026 · Specification research, not a field test
PUT THIS GUIDE TO WORK
See published mismatches and the checks still needed.
BEST MATCHES FOR THE WORKMASTER 35
13 of 19 pto wood chippers we track pass the published power, hitch and speed screen. Each still has a detail to confirm with the seller.
PTO chipperWoodland Mills
4″ max. chip diameter · 15–30 PTO hp
Confirm the conflicting tractor specifications in your serial-specific manual; official source values differ.
PTO chipperWoodland Mills
6″ max. chip diameter · 20–50 PTO hp
Confirm the conflicting tractor specifications in your serial-specific manual; official source values differ.
PTO chipperWoodMaxx
9″ maximum chip diameter, inches · 25 PTO hp minimum; maximum not stated
Confirm the complete operating weight; a shipping weight cannot establish the attachment load.
PTO chipperWallenstein
5″ max. chip diameter · 30–55 engine hp · current U.S. page (manual table: 40–55 hp for the BX52R)
Confirm the correct attachment and driveline configuration for the tractor’s PTO speed; listed speed options are discrete settings.
PTO chipperFarmer-Helper
4″ published feed-capacity short side, inches · 15–45 PTO hp in current index-linked manual; older/page conflicts retained
Confirm the complete operating weight; a shipping weight cannot establish the attachment load.
PTO chipperFarmry
5″ max. chip diameter · 15–45 engine hp
Confirm the conflicting tractor specifications in your serial-specific manual; official source values differ.
7 more possible options in the full comparison table.
THE DECISION IN NUMBERS
These are conditional checks against two documented mechanical ratings. Neither is assigned universally to all WORKMASTER 35 tractors. Full-diameter/full-feed conditions and complete operating loads remain separate from the basic power band.
Scroll the table sideways on smaller screens.
| Chipper | Published power requirement | 29.7 brochure / 27.4 manual result | Capacity or load qualification |
|---|---|---|---|
| WC46 | 15–30 PTO hp | 0.3 / 2.6 hp below maximum | Both above over-20 full 4-inch/full-feed threshold |
| WC68 | 20–50 PTO hp | 9.7 / 7.4 hp above minimum | Both below over-40 full 6-inch/full-feed threshold |
| MX-9900 | 25 PTO hp minimum; no finite maximum stated | 4.7 / 2.4 hp above minimum | 816 lb approximate dry weight; complete operating mass unknown |
The brochure and PIN-scoped manual are both official. Their 29.7 and 27.4 mechanical PTO figures are preserved here rather than averaged or explained by an invented year change. Both remain inside WC46’s band, but the brochure leaves only 0.3 hp to its published maximum. Confirm the actual tractor specification and the chipper’s permitted input; a numeric band check is not manufacturer approval.
Both figures exceed the WC46 condition for full 4-inch logs at full feed speed. Neither reaches WC68’s over-40-PTO-hp condition for full 6-inch logs at full feed speed. The larger WC68 may still serve a different branch-handling need within its operating band, but it cannot be presented as an equal-speed capacity upgrade. Wood condition and feeding practice remain part of the maker’s guidance.
MX-9900 clears its 25-PTO-hp minimum under both values. Its 9-inch nominal capacity and 816 lb approximate dry weight do not establish full-capacity output or a complete operating load; shaft, oil and supplied configuration must be confirmed. WC46 and WC68 list 587 and 747 lb product weights on their retained manual bases. The tractor’s 1,433 lb at 24 inches is a load-center reference, not a simple subtraction allowance.
WC46 and WC68 have self-contained hydraulic feed; MX-9900 uses its own hydrostatic feed arrangement. None depends on the WORKMASTER’s optional rear valves. Instead, confirm the independent rear PTO’s stationary-use setup for the mechanical and shuttle controls. Manual page 4-9 specifies the controls and interlocks, while page 9-5 gives 2,509 engine rpm for rear 540; use the manual that applies to the actual PIN.
Wallenstein’s current pages rate the 5-inch BX52RI (30–55 engine hp, Category I). Two hydraulic rollers pull material in at a set rate, and P3 PULSE reverses them when the rotor slows; they need 3–6 gpm from a rear remote or Wallenstein’s PTO-driven power pack. The New Holland WORKMASTER 35’s 35 engine hp is inside the BX52RI page’s 30–55 but under the 40 that the manual’s table gives for the BX52R, so ask Wallenstein which floor applies to the serial on offer. Its published lift at 24 inches, 1,433 lb, carries the 845-lb BX52RI with 588 lb to spare. Wallenstein lists no price; ask a dealer.
THE SCREEN, WITH ITS LIMITS VISIBLE
No pairing below is manufacturer-confirmed. “Preliminary” still requires implement limits, load center, ballast, hitch geometry and shaft checks.
Initial specification screen only. Scroll the table on small screens. Read the product page for every remaining check.
| Attachment | 12×12 synchronized shuttle · 4WD · ROPS · brochure 29.7 PTO hp; manual observed 27.429.7 PTO hp |
|---|---|
| Farmry WCAP5 →412 lb · Net weight WITH PTO shaft, manual Rev1.5 p20 | Needs specification reviewConfirm the conflicting tractor specifications in your serial-specific manual; official source values differ. |
| Farmry WCAP5 PRO →386 lb · Product weight, current manual Rev1.4 p13; whether PTO shaft is included in this weight is not stated | Needs specification reviewResolve the conflicting published specifications for the exact model revision. |
| Woodland Mills WC46 →587 lb · Product weight, 2024 operator manual Rev C p9 | Needs specification reviewConfirm the conflicting tractor specifications in your serial-specific manual; official source values differ. |
| Woodland Mills WC68 →747 lb · Product weight, 2024 operator manual Rev C p9 | Needs specification reviewConfirm the conflicting tractor specifications in your serial-specific manual; official source values differ. |
| Woodland Mills TFG55 PTO →346 lb · Product weight, Rev B manual p9 | Needs specification reviewResolve the conflicting published specifications for the exact model revision. |
| Woodland Mills WC88 →900 lb · Product weight: 900 lb in current linked 2022 Rev C manual, printed p9; shipping weight is 1,054 lb. The manual does not explicitly identify whether quoted product weight includes the PTO shaft or filled hydraulic oil. | Published mismatch29.7 PTO hp is below the 35 hp minimum. |
| WoodMaxx WM-8H →Operating weight unconfirmed · Operating weight is unverified in the current official product page and linked manual. The page lists 990 lb SHIPPING weight; do not use it as operating weight. Confirm weight with PTO shaft and a filled hydraulic tank. | Needs specification reviewConfirm the complete operating weight; a shipping weight cannot establish the attachment load. |
| WoodMaxx WM-8M →775 lb · Product page states 775 lb total weight on the three-point hitch; shaft/fluid inclusion is not explicit. Shipping sections conflict at 950 versus 990 lb. Confirm the delivered operating assembly and shipping revision. | Needs specification reviewResolve the conflicting published specifications for the exact model revision. |
| WoodMaxx MX-8800 →Operating weight unconfirmed · Complete operating weight is unverified. Current Rev D manual (printed p45 / pdf p46, technical specifications) states approximately 772 lb DRY weight; page separately states 1,004 lb SHIPPING weight. Shaft inclusion in dry weight is not explicit. Do not substitute either figure for a confirmed shaft/oil-inclusive operating load. | Needs specification reviewConfirm the complete operating weight; a shipping weight cannot establish the attachment load. |
| WoodMaxx MX-9900 →Operating weight unconfirmed · Complete operating weight is unverified. Current Rev C manual (printed p42 / pdf p43, technical specifications) states approximately 816 lb DRY weight; page separately states 1,048 lb SHIPPING weight. Shaft inclusion in dry weight is not explicit. Do not substitute either figure for a confirmed shaft/oil-inclusive operating load. | Needs specification reviewConfirm the complete operating weight; a shipping weight cannot establish the attachment load. |
| Farmer-Helper FH-BX42 →Operating weight unconfirmed · Complete operating weight is unverified. Current index-linked manual p2 lists 430 lb net and 450 lb shipping. Current product/series pages instead list 423 lb net and 458 lb shipping. Net-weight shaft/assembly inclusions are unstated; none is substituted for a verified operating load. | Needs specification reviewConfirm the complete operating weight; a shipping weight cannot establish the attachment load. |
| Farmer-Helper FH-BX62S →Operating weight unconfirmed · Complete operating weight is unverified. Current index-linked manual p2: 830 lb net / 860 lb shipping. Current series page: 835 lb net / 915 lb gross. Product page calls 835 lb both total and gross; older product-linked manual p38 gives 797 lb net / 850 lb gross. Shaft/assembly inclusions are unstated, so no reference is used as operating weight. | Needs specification reviewConfirm the complete operating weight; a shipping weight cannot establish the attachment load. |
| Wallenstein BX36S →Operating weight unconfirmed · Official page Total Weight and Jan-2025 manual Weight: 395 lb. Neither states whether the supplied shaft and all operating equipment are included; complete operating and separate shipping weights remain unverified. | Published mismatch35 engine hp exceeds the published 30 hp range. |
| Wallenstein BX52S →Operating weight unconfirmed · Official page Total Weight and Jan-2025 manual Weight: 505 lb. Neither states whether the supplied shaft and all operating equipment are included; complete operating and separate shipping weights remain unverified. | Needs specification reviewConfirm the correct attachment and driveline configuration for the tractor’s PTO speed; listed speed options are discrete settings. |
| Wallenstein BX72S →Operating weight unconfirmed · Current official page Total Weight and Jan-2025 manual Weight: 728 lb. Neither defines complete shaft-inclusive operating mass or a separate shipping weight. Confirm the assembled operating load; do not relabel 728 lb as dry or shipping weight. | Published mismatch35 engine hp is below the 50 hp minimum. |
| Wallenstein BX102S →1143 lb · Total Weight 1143 lb (519 kg) on the current page and in the Jan-2025 BX-S manual. Neither says whether the PTO shaft is included; confirm the assembled operating load. | Published mismatch35 engine hp is below the 80 hp minimum. |
| Wallenstein BX52RI →845 lb · Total weight 845 lb on the current page and operating weight 845 lb in the BXR manual §10.1. Neither says whether the PTO shaft is included. | Needs specification reviewConfirm the correct attachment and driveline configuration for the tractor’s PTO speed; listed speed options are discrete settings. |
| Wallenstein BX72RI →1300 lb · Total weight 1,300 lb on the current page and operating weight 1,300 lb in the BXR manual §10.1. Neither says whether the PTO shaft is included. | Published mismatch35 engine hp is below the 45 hp minimum. |
| Wallenstein BX102RI →1950 lb · Total weight 1,950 lb on the current page and operating weight 1,950 lb in the BXR manual §10.1. Neither says whether the PTO shaft is included. | Published mismatch35 engine hp is below the 75 hp minimum. |
Should I buy the WC46 or WC68 when my compact tractor is near 20 PTO hp?
Read the guide →FIELD GUIDETake the complete setup, not just a horsepower number, to the manufacturer.
Read the guide →FOLLOW THE NUMBERS
Research record reviewed November 7, 2026. Confirm the current manual and the exact revision supplied with your machine.